Quick answer: A little planet is a stereographic reprojection of a full 360×180 panorama. Take a finished equirectangular image (or the original 360 project) in Hugin, set the projection to Stereographic, rotate the view so the ground — the nadir — sits in the centre, choose a square-ish canvas, and render. If your source does not cover the whole sphere, the planet gets a hole or a torn edge; full-sphere input is the whole secret.
What a little planet actually is
The “little planet” (or tiny planet) look wraps the world into a floating ball: the ground becomes a disc in the middle, buildings and trees sprout from its edge, and the sky wraps around the outside. It is not a filter — it is the stereographic projection, a mathematically respectable way of flattening a sphere that happens to look delightful. Hugin includes Stereographic among its output projections, so if you already have a 360 panorama project, you own everything needed. If you do not have a 360 set yet, start with our 360 stitching guide; a little planet is a five-minute detour at the end of that workflow, not a separate discipline.
Start from a full-sphere source
The requirement that makes or breaks the effect: the source must cover the entire sphere, 360×180 degrees. A wide but partial panorama cannot wrap into a closed ball — the missing sky or ground becomes a wedge-shaped gap or a smeared pole. Two ways in:
- From a 360 project: open the saved .pto project you stitched the equirectangular from, and simply change the output — the original photos give you the best quality.
- From a finished equirectangular file: create a new project, add the equirectangular image as a single photo, and set its lens type to Equirectangular with a 360-degree field of view. Hugin now treats the file as a complete sphere it can reproject.
Either way, check the nadir before you start: whatever is at the bottom of the sphere becomes the centre of your planet, so a visible tripod sits right in the middle of the picture. Patch it first — see our nadir patching guide — or plan a composition where the centre is plain ground.
Set the stereographic projection
Open the Fast Preview window and set the output projection to Stereographic. The sphere collapses into a disc as you watch. Now rotate the view: you want to look straight down at the nadir, so adjust the pitch by 90 degrees — using the drag tools or the numerical rotation in the preview — until the ground occupies the centre and the horizon forms a ring around it. (Rotate the other way and you get the inverted variant, a “tunnel” or “tube” view with the sky in the centre — a legitimate effect in its own right, and a useful signpost that you turned the sphere the wrong way.) Roll rotates the planet in its frame; use it to place a dominant feature — a road, a river, the shoreline — where you want it in the composition.
Frame and size the canvas
In the Stitcher tab, choose the canvas. Square formats suit the classic planet; a wider canvas leaves sky around a smaller ball, a tighter canvas crops the ball’s edge into an abstract ring. Resolution follows your source: you cannot invent pixels, and the stereographic mapping spends most of them on the centre, so start from the largest equirectangular you have. Keep the projection’s field of view at the full sphere; trimming it zooms the planet but quickly exposes the edge artefacts discussed below. Render a TIFF master as usual, per the workflow in our main tutorial, and export JPG copies for sharing.
Common failures and fixes
- A wedge is missing or the ball will not close: the source was not a full 360×180 sphere. Re-shoot or re-stitch including zenith and nadir frames; there is no setting that substitutes for missing coverage.
- The centre is a smeared starburst: that is the pole of your equirectangular being magnified. A clean, well-covered nadir (ideally a dedicated nadir frame) keeps the centre sharp; a clear sky at the zenith smears less noticeably than detailed ground does at the nadir.
- The horizon ring is wavy: the source panorama was not level. Level the sphere in the original project first — a tilted horizon becomes a lopsided planet.
- Buildings at the edge bend oddly: inherent to stereographic mapping at extreme angles. Choosing a different roll, or a slightly smaller field of view, moves the worst distortion away from your subject.
Little planets from drone and travel shots
Some of the most-shared little planets start as drone panoramas: a full sphere captured above a coastline, a village or a landmark, where the ground pattern itself is the picture. The Hugin workflow is unchanged — the drone’s stitched equirectangular, or its source frames if you stitch them yourself, becomes the input sphere — but the centre of the planet is now the landscape directly below the drone rather than a tripod patch, so the nadir problem mostly disappears and roads, rivers and field boundaries draw the composition for you. Travel photography is the other natural source: one 360 set from a viewpoint, a market square or a temple courtyard yields the conventional tour panorama for your archive and the planet for sharing, from the same shutter presses.
For sharing, export the planet at a generous size — social platforms compress aggressively, and the fine detail at the planet’s edge suffers first — and keep the square crop. If the centrepiece of the ball is a recognisable place, a small caption naming it outperforms the image alone, because viewers read the planet as abstract until the location clicks.
Ideas worth stealing
Little planets reward strong geometry: a beach with a clean shoreline, a plaza with radial paving, a forest clearing, a sports field with painted lines. City squares work beautifully because the architecture rings the planet like a crown. Keep one dominant vertical — a tower, a lighthouse, a single tree — and roll the view so it stands at the top of the ball. And keep the full-sphere project: from the same source you can render the normal equirectangular, the planet, and the tunnel, which makes one shoot produce a small series instead of a single image.
FAQ
Can I make a little planet from a normal (non-360) panorama?
Not a closed one. Stereographic reprojection needs the full 360×180 sphere; a partial panorama leaves a wedge-shaped gap where the missing coverage belongs. Shoot or stitch a complete sphere first.
Which projection does Hugin use for little planets?
Stereographic. Set it as the output projection in the Fast Preview, rotate the sphere so the nadir is centred, and render. The opposite rotation produces the inverted “tunnel” look.
Why is the middle of my planet blurry?
The centre of the planet is the nadir of your panorama, where equirectangular pixels are most stretched and coverage is thinnest — especially if the tripod area was never properly photographed. A dedicated nadir frame fixes it.
What canvas size works best for a little planet?
Start square, at the full resolution your source supports. The stereographic projection concentrates detail in the centre, so a larger source equirectangular (8000×4000 or more) gives noticeably cleaner planets.
